Plan the perfect garden with our interactive tool →

5-HP Tecumseh Engine Snowblower Won't Run Without Full Choke

Close-up of snow
Hemera Technologies/AbleStock.com/Getty Images

The Tecumseh engine on your snowblower may need to run on "Full" choke temporarily under certain conditions, but if you have to leave it in full choke to operate the machine sustainably, something is not right. Troubleshoot. You'll need to consider cold starting, needle-valve air-intake adjustments and carburetor cleaning. Troubleshooting might get you back blowing snow even if you have no experience working on a Tecumseh engine.

Cold Start and Sputtering

Consider the conditions under which you are attempting to start the 5-horsepower Tecumseh engine. A "cold start" occurs when the engine is completely cold and has not been used recently. Additionally, temperatures outside can increase this effect. It's recommended to always adjust the throttle to full choke when starting a Tecumseh engine completely cold. Ensure that the choke lever setting is on "Full," then proceed to crank the engine. Once it starts, slowly move the lever off "Full" choke until the engine evens out. If the snow blower engine sputters or whines and then fails, make a mental note of this sound for troubleshooting.

  • The Tecumseh engine on your snowblower may need to run on "Full" choke temporarily under certain conditions, but if you have to leave it in full choke to operate the machine sustainably, something is not right.

Needle Valve Adjustment

Find the carburetor, located halfway up the left side of the engine. It is distinctive because of the immediately recognizable bowl shape. Locate the slender needle valve near the bottom of the carburetor bowl. This adjusts air intake into the engine and could be the reason for the sputtering and winding out of the engine following the cold start. Turn the needle valve all the way to the right, then get the Tecumseh engine running on choke. Back slightly off the choke, just enough to get the engine sputtering and whining again. While listening to this noise, turn the needle valve back to the left a quarter turn. Listen to any change to the engine's sputtering. If it continues, continue making gradual quarter turns, to the left, to the needle valve until the engine smooths out. These valve adjustments may prove enough to get the engine running without failing even when the choke lever is backed entirely off "Full."

  • Find the carburetor, located halfway up the left side of the engine.
  • Turn the needle valve all the way to the right, then get the Tecumseh engine running on choke.

Carburetor Bowl Cleaning

Begin to disassemble the carburetor bowl for cleaning if the Tecumseh engine still won't properly run off choke even after persistent needle valve adjustments. Ensure the engine is off, then place a dish under the bottom of the carburetor bowl. Remove the nut on the bowl's underside using a socket wrench. Wait as excess fluid drains from the Tecumseh engine into your dish. After this process finishes, screw off the carburetor bowl with your hands and clean its inside out with a cloth and a carburetor cleaning solution. Scrub the bowl's removed nut with a wire brush and the cleaning solution.

Carburetor Reassembly and Final Adjustments

Screw the Tecumseh engine's carburetor bowl back onto the engine, then tighten its removed nut into the underside of the bowl with clockwise turns from your socket wrench. Your engine will now run efficiently, although upon starting the engine you may need to tweak the position of the needle valve again now that the carburetor has been cleaned. Alter the needle valve slightly just as you did before while listening for engine sputtering. Continue with adjustments until all sputtering and whining ceases and the engine runs smoothly without relying on the choke.

  • Begin to disassemble the carburetor bowl for cleaning if the Tecumseh engine still won't properly run off choke even after persistent needle valve adjustments.
  • Your engine will now run efficiently, although upon starting the engine you may need to tweak the position of the needle valve again now that the carburetor has been cleaned.

Related Articles

How to Repair a Murray Riding Lawnmower Carburetor
How to Repair a Murray Riding Lawnmower Carburetor
How to Adjust the Idle in a Honda OHV Lawn Mower
How to Adjust the Idle in a Honda OHV Lawn Mower
How to Troubleshoot a Briggs & Stratton Quantum 6.5 HP
How to Troubleshoot a Briggs & Stratton Quantum 6.5...
How to Rebuild a Briggs & Stratton 12 HP Carburetor
How to Rebuild a Briggs & Stratton 12 HP Carburetor
How to Repair a Toro Lawnmower That Stalls After Starting
How to Repair a Toro Lawnmower That Stalls After Starting
Will A Clogged Exhaust on Lawn Mower Stop The Engine?
Will A Clogged Exhaust on Lawn Mower Stop The Engine?
How to Adjust a Carburetor on a Ryobi Grass Trimmer
How to Adjust a Carburetor on a Ryobi Grass Trimmer
Craftsman 6.0 Mower Troubleshooting
Craftsman 6.0 Mower Troubleshooting
How to Adjust the Idle Screw on a Leaf Blower
How to Adjust the Idle Screw on a Leaf Blower
How to Test a Lawn Mower Ignition Coil
How to Test a Lawn Mower Ignition Coil
How To Repair a John Deere Carb
How To Repair a John Deere Carb
How to Troubleshoot a John Deere 4200
How to Troubleshoot a John Deere 4200
Garden Guides
×